Ungreased Japanese AS332L Tail Rotor Fatally Failed (Toho Air Sevices JA9672)

On 8 November 2017, Airbus Helicopters AS332L Super Puma JA9672 of Toho Air Service crashed in Gunma prefecture after the tail rotor separated from the aircraft as the crew prepared to make an emergency landing.  There were four people on board, who all died.  There was a post crash fire.

Wreckage of Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Wreckage of Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

The Japan Transport Safety Board (JTSB) concluded in their safety investigation report  (published in Japanese on 23 April 2020) that:

  • It is highly probable that the crash occurred because the tail rotor separated from the aircraft when it tried to make an emergency landing due to abnormal vibration that occurred during the flight…
  • The tail rotor separated from the fuselage because the spindle bolt of the white tail rotor blade flapping hinge broke and the tail rotor became unbalanced…
  • It is presumed that the spindle bolt broke because the bearing of the flapping hinge was damaged [which] was not detected by inspection.

The following JTSB presentation slides that we have translated show the accident sequence:

Flightpath of Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Flightpath of Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Accident Sequence of  Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Accident Sequence of Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Severing of the Tail Boom Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Severing of the Tail Boom Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Wreckage of Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Wreckage of Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

These graphics illustrate how lucky the 17 occupants of Bond AS332L G-PUMH were in 1995 when a tail rotor flapping hinge retainer had failed due to a fatigue crack emanating from a grease nipple hole while returning from a North Sea offshore installation.  G-PUMH was able to make a safe landing at Longside, near Peterhead.

Background

Toho use their AS332Ls for construction projects.

Early in the history of the of the AS332L, the manufacturer had noticed that using Shell Aeroshell 14 grease in tail rotor pitch change hinge bearings had increased the tendency for false brinelling to occur.  In 1991 Exxon Mobil MOBILPLEX 47 grease was introduced as an alternative.  This was a great success but in February 2008 production of MOBILPLEX 47 was abandoned.  Subsequently the manufacturer noticed that on the return to the inferior Shell grease a…

…reduction in the reliability of the tail rotor hub bearing [occured], especially within the helicopter operating range under hot and humid conditions.

Coincidentally, before this accident occurred on 6 December 2016, Aerossurance spoke at a breakout session organised by EASA at their 10th Rotorcraft Symposium in Cologne on rotor and rotor drive system safety.  One of the points made in that session was that a crucial contribution that the oil industry can make to helicopter safety is the production of optimised lubricants, even though they may have a small market.

The continued airworthiness of the five AS332L tail rotor flapping hinges were reliant on greasing every 10 flying hours (or daily if parked in hot and humid conditions), as well as 50 and 250 hour inspection.  The newer four bladed AS332L2 and EC225 tail rotors feature an improved design.

Structure of Airbus Helicopters AS332L - Note Inner / Outer 'Rings' = 'Races' (Credit: JTSB)

Structure of Airbus Helicopters AS332L Tail Rotor Hub Flapping Hinge – Note Inner / Outer ‘Rings’ = ‘Races’ (Credit: JTSB)

JTSB could not find evidence of a seal replacement on that blade since June 2014 and postulate the seal had been deteriorating by 2017.  As the aircraft was parked outside in high humidity during summer 2017 that would have allowed moisture ingress into the grease.  Unfortunately it appears the maintenance personnel were not aware that they should have re-greased the tail rotor due to the humid environment each day either.

Inspections from July 2017 started to show the grease in the white blade’s hub starting to turn increasingly black and by September 2017 “movement of the white blade was not smooth”.  JTSB believe these were indications of bearing deterioration.  However, no corrective maintenance action was taken initially.

The aircraft was subject to a 250 hour inspection 20-23 September 2017.  The white blade’s inner race was found cracked and  the inner race and the stop washer were replaced.  JTSB note that:

The condition of the outer bearing was not confirmed, and the seal was not replaced.

The seal replacement was a Maintenance Manual requirement.  They also postulate that as the new inner race was used to force out the damaged old inner race, that some debris may have been left behind.  The level of damage to the inner race should have required notification to Airbus too say JTSB.  This was not done.

From around 31 October 2017, low-frequency c 1Hz lateral vibration was  felt in the cockpit.  The aircraft was not fitted with HUMS and this was misdiagnosed as due to a slight oil leak from the lip seal of the sleeve of a main rotor blade.

Flapping Hinge Bearing Damage Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Flapping Hinge Bearing Damage Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Post-accident laboratory examination concluded that the cracks in the spindle bolt of the aircraft showed a “twisted state” indicating that the spindle bolt was subjected to an “unexpected fatigue load”.  They demonstrate in their report this was most likely due to the bearing deterioration.

Loads in Tail Rotor Flapping Hinge Bolt Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Loads in Tail Rotor Flapping Hinge Bolt Toho Air Services Airbus Helicopters AS332L JA9672 (Credit: JTSB)

Continued Airworthiness Action

On 21 November 2017, less than two weeks after the accident, Airbus Helicopters EASB No. AS332-64.00.43 was issued which was referenced by EASA Emergency Airworthiness Directive (EAD) No.2017-0232-E.  This AD required…

…a one-time inspection of flapping hinges of the tail rotor blades and, depending on findings, corrective action(s) [and] reporting of the detected findings and sending any cracked components to AH to support the investigation.

In February 2018 this was expanded to include the similar SA330J Puma.

On 15 November 2018, Airbus Helicopters EASB No. AS332-05.01.10 was issued, covered by EASA Airworthiness Directive (AD) No.2018-0248, which required component replacements.

The latest EASA AD is No.2020-0086.

UPDATE 6 August 2021: This accident will be subject of a JTSB presentation at the ISASI 2021 virtual seminar.

Safety Resources

Maintenance Observation Programme (MOP)

Aerossurance worked with the Flight Safety Foundation (FSF) to create a Maintenance Observation Program (MOP) requirement for their contractible BARSOHO offshore helicopter Safety Performance Requirements to help learning about routine maintenance and then to initiate safety improvements:

mop

Aerossurance can provide practice guidance and specialist support to successfully implement a MOP.


Aerossurance’s Andy Evans was recently interviewed about safety investigations, the perils of WYLFIWYF (What-You-Look-For-Is-What-You-Find) and some other ‘stuff’ by with Sam Lee of Integra Aerospace:

https://www.youtube.com/watch?v=QQF8jW9lrG8


Aerossurance has extensive air safety, flight operations, SAR, airworthiness, human factors, aviation regulation and safety analysis experience.  For practical aviation advice you can trust, contact us at: enquiries@aerossurance.com